Ni-NTA Sepharose FF Gravity Prepacked Column

Ni-NTA Sepharose FF Gravity Prepacked Column

¡¾Numbering¡¿BK-NRPB57S ¡¾CAS¡¿CAS
¡¾Item No.¡¿BK-NRPB57S-Z25 ¡¾specification¡¿
5 minutes to choose the product plan

E-mail£ºcro@szbknm.com




Product name: Ni-NTA Sepharose FF


English name: Nickel Nitrilotriacetic acid NUPharose Fast Flow, Ni-NTA NUPharose FF


Specifications: 20 ml, 100 ml, 1L, 1 ml pre-packed column, 5 ml pre-packed column, special specifications customized


Transportation: 2 ~ 30¡æ, normal pressure, avoid light


Storage: 20% ethanol, 2 ~ 25¡æ


Shelf life: 5 years






Related introduction:


Ni-NTA Sepharose FF is based on agarose microspheres, coupled with nitrilotriacetic acid (NTA) through activation, and then chelate Ni2+. Compared with iminodiacetic acid (IDA), it has better chelating agent, reducing agent, and alkali tolerance. If the sample contains 1-10mM EDTA or 1-10mM ¦Â-mercaptoethanol or 5mM DTT, it can be normal Purification; in the case of chelating nickel, it can also be cleaned with 0.1M NaOH.






Ni-NTA Sepharose FF is mainly used to purify recombinant proteins with histidine tag (His-Tag). The purification principle is that the imidazole ring of the histidine tag of the recombinant protein can form a stable coordination bond with the transition metal Ni2+, so it can be specifically, firmly and reversibly adsorbed to the matrix that fixes these metal ions, combined with the His-Tag recombinant protein Ni-NTA Sepharose FF is generally eluted by increasing the concentration of imidazole.






Technical index:


Matrix


4% agarose gel


Ligand


-N(CH2COOH)3


Ligand Density


¡Ý15 ¦Ìmol/ml


Filler particle size


60~180 ¦Ìm


Maximum flow rate


800 cm/h


Recommended flow rate


50-100 cm/h


pH stability


pH 5-12, pH 3~13


Back pressure resistant


0.3 MPa


Capacity


¡Ý20 mg His-tag recombinant protein/ml






Instructions:


1. Column packing


(1) The temperature of all materials that need to be used should be the same as the temperature of the chromatographic operation, and the liquid is best to be degassed.


(2) Add distilled water to the lower end of the column to remove the air in the column, close the outlet of the column, and leave a small amount of distilled water in the column.


(3) When continuously pouring the agarose gel into the column, use a glass rod close to the inner wall of the column for drainage to reduce the generation of bubbles and allow the filler to settle naturally.


(4) The column pressure should not exceed 0.3 MPa. If the column pressure cannot be measured in the column packing system, the column should be packed at normal flow rate.


(5) The filled Ni-NTA Sepharose FF column is equilibrated with 2-5 column volumes of the initial buffer solution, and the recommended flow rate is 100 cm/h. The equilibrated column can be used for loading His-Tag recombinant protein And elution purification.


2. Sample loading


(1) Buffer selection: Generally, the binding buffer with pH 6-8 is used. Commonly used buffers include 10-00mM sodium phosphate buffer, 20-200mM Tris-HCl buffer, etc. Generally, 0.15-0.5M NaCl should be added to the buffer to eliminate ion exchange. When using Ni-NTA Sepharose FF for the first time, it is recommended to use 50mM PBS (50 mM NaH2PO4, 0.5M NaCl, NaOH to adjust pH 7.4) as the binding buffer.


(2) Sample processing: The sample buffer should be consistent with the selected binding buffer. In order to ensure the consistency of the buffer, the bacteria can be broken in the binding buffer, or the pH can be adjusted to be consistent with the binding buffer, or exchanged to the binding buffer (common methods include dialysis, ultrafiltration, desalting column exchange, etc.), or use the binding buffer The solution is diluted 2-10 times and so on. The sample should be filtered with 0.45¦Ìm before loading the column.


3. Elution


(1) The most commonly used elution method for Ni-NTA Sepharose FF is to increase the concentration of imidazole for elution.


(2) Imidazole is alkaline, and pH should be adjusted with HCl after preparation of the corresponding buffer.


(3) When using Ni-NTA Sepharose FF for the first time, I don¡¯t know the eluted imidazole concentration. It is recommended to add 10mM, 20mM, 50mM, 100mM, 200mM, 500mM imidazole to the binding buffer, and the concentration ranges from low to high. Separately eluted and collected, and identified the eluted components by SDS-PAGE electrophoresis and other methods.


(4) If conditions permit, linear imidazole gradient elution can also be performed to determine the best elution conditions.


4. Cleaning in place


In-place cleaning is required after multiple uses. The common method is to wash with 5 column volumes of distilled water, then wash with 1-3 column volumes of 50mM NaOH for 10-20min, and immediately wash with 5 column volumes of binding buffer (50mM PBS). balance.

Warm tips: Suzhou Beike nano products are only used for scientific research, not for human body,different batches of products have different specifications and performance

Message

Name£º *
Mobile£º *
E-mail£º *
Content£º
 
Scan code concerns WeChat official account
QQCommunication group£º1092348845
Warm tips: Suzhou Beike nano products are only used for scientific research, not for human body,different batches of products have different specifications and performance.The website pictures are from the Internet. The pictures are for reference only. Please take the real object as the standard. In case of infringement, please contact us to delete them immediately.
    Ni-NTAÇíÖ¬ÌÇÄý½ºFFÖØÁ¦Ô¤×°Öù

Previous£º the end...

Next£º Dextrin Sepharose FF

advisory
phone
cro@szbknm.com
Tel:+8618915694570
scan

scan
WeChat